GLOAPM.COMNach Rang
Nach Rang
Nach Schiffstyp
Auf der Karte
Maritime Nachrichten
Für Segler
Für Unternehmen
Suche nach aktuellen Stellenangeboten:
Filter anzeigen
Lebenslaufsuche für Seeleute:gemeinsame Basismeine Basis
Heim Online-Tests CES Ro-Ro Cargo MASTER / Ch-Officer Test for seamans about Deck department, Management level, Roro Cargo Vessel (CES v6.0)
Online-Test: Test for seamans about Deck department, Management level, Roro Cargo Vessel (CES v6.0)
Wählen Sie den Testmodus:
Ausbildung
Online-Test
Beschreibung
Rezensionen
Frage 1 aus 64
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
- 13
- 14
- 15
- 16
- 17
- 18
- 19
- 20
- 21
- 22
- 23
- 24
- 25
- 26
- 27
- 28
- 29
- 30
- 31
- 32
- 33
- 34
- 35
- 36
- 37
- 38
- 39
- 40
- 41
- 42
- 43
- 44
- 45
- 46
- 47
- 48
- 49
- 50
- 51
- 52
- 53
- 54
- 55
- 56
- 57
- 58
- 59
- 60
- 61
- 62
- 63
- 64
According to Rule 24 of the International Regulations for Preventing Collisions and the illustrated lights, how long is the tow likely to be?
It exceeds 200 metres.
At least 100 metres.
It is less than 200 metres.
It is more than 50 metres but less than 200 metres.
On a conventional rudder, how much lift force remains if the rudder-angle is decreased to 20 degrees, from an initial 35 degrees?
About 80 %.
About 50 %.
About 30 %.
About 10 %.
You are on a vessel 10 nautical miles off the coast of Nigeria, West Africa. Are you allowed to dump empty glass bottles overboard?
Yes, glass bottles can be dumped overboard.
Yes, the bottles can be dumped if they are ground so that the resulting particles can pass through a screen with 25 mm openings.
No, glass bottles can not be dumped overboard.
Yes, the bottles can be dumped if they are ground so that the resulting particles can pass through a screen with 50 mm openings.
For which ships is the SOLAS convention applicable?
For tankers and other vessels carrying persistent oil as cargo.
For all vessels expect passenger vessels.
For all vessels.
For passenger vessels only.
Who are responsible for safe working conditions onboard?
Master, Chief Engineer & Chief Officer.
The safety officer.
The officer of the watch.
The individual person.
The emergency fire pump is in accordance with good seamanship and precautionary routines run and tested weekly. Routine checks and maintenance are normally carried out by dedicated personnel. To ensure safe and appropriate operation of the pump, would you consider it beneficial that the same dedicated personnel operate the pump in emergencies?
Only senior engineers should operate the emergency pump.
To ensure safe operation of the emergency pump, only dedicated personnel must be permitted to operate the pump.
Only senior deck officers should operate the emergency pump.
In case of accidents, it is important that a wide range of personnel must be permitted and trained to operate the pump.
What is the minimum number of portable two way VHF walkie talkies for use in survival craft, that should be carried onboard vessels which comply with GMDSS regulations?
3 sets.
2 sets.
1 set.
There is no requirement to carry them.
What is the result of a “high metacentric height”?
The vessel will roll slowly or be unstable.
The vessel will roll violently.
The vessel will have a great bending moment.
The vessel’s tweendeck height is too high.
Your watchkeeper has just informed you that the vessel has collided with a sailing vessel. What action should be taken?
Call the company, explain the situation and ask for orders.
Do nothing and wait for assistance.
Alarm the rescue centre and commence searching for any survivors.
Leave the position as fast as possible.
What corrections must be applied to the echo sounder reading to compare the depth of water with the depth printed on the chart?
Draught of the ship.
Allowance for the ships speed.
Shallow water effects.
The distance between the pulse Transmitter and Receiver.
Is there any special area where it is forbidden to pump out any sludge or oil residues?
There isn’t any special area where it is forbidden to pump out any sludge or oil residues.
There is 5 special area where it is forbidden to pump out any sludge or oil residues.
There is 4 special area where it is forbidden to pump out any sludge or oil residues.
There is 3 special area the Baltic, Mediterranean and the Black sea where it is forbidden to pump out any sludge or oil residues.
The authority to order the use of distress signal or distress alerts is:
Only with the master.
The first person to discover the distress situation.
The person designated to maintain communication during distress situations.
I don’t know.
The word SHIP is spelled conform the international phonetic alphabet:
Sierra, Hotel, India, Papa.
Singapore, Hotel, India, Paris.
Sierra, Hotel, Item, Papa.
Sugar, Hotel, Italia, Peter.
To get priority with radio-communication, one must notify the coast-station that the call is:
A priority call.
A personal call.
An urgent call.
I don’t know.
One wishes to have a telephone conversation with a person whose name is known. This is what is called:
A priority call.
A personal call.
A direct call.
I don’t know.
Inmarsat Telex Service code “31” can be used:
To ask for maritime inquiries.
When the coast-station is disfunctional.
When technical problems are experienced with the Inmarsat terminal.
I don’t know.
Inmarsat Telex Service code “33” can be used:
When the coast-station is disfunctional.
When technical problems are experienced with the Inmarsat-terminal.
To ask for maritime enquiries.
I don’t know.
For a “distress alert” via the DSC, the MF-brand is used in the frequencies:
TX: 2 177,0 kHz, RX: 2 177,0 kHz.
TX: 2 189,5 kHz, RX: 2 189,5 kHz.
TX: 2 187,5 kHz, RX: 2 187,5 kHz.
I don’t know.
When may a call for radio medical advice be preceded by the urgency-signal:
When you have a doctor on board.
In urgent cases.
Always.
Never.
When a character in the NAVTEX message sent is not received in the proper way:
A closely resembling character will be printed.
Any other character will be printed.
The message will not be printed at all until, with repeated transmission, it can be automatically compared and corrected.
Nothing or a special character will be printed.
To prevent overload of the MF/HF transmitter:
Do not leave the transmitter on stand-by for too long, if not required.
Clean the dust filter of the fan regularly.
Switch over to low power intermitently.
Do not transmit to long at full power.
Testing a SART is permitted:
Only in a port or harbour.
Only at sea, outside territorial waters.
At sea, outside territorial waters, and in a port or harbour.
I don’t know.
The batteries must be placed in a well ventilated place, so that:
There is sufficient oxygen available for optimum working of the batteries.
The detonating gas can be discharged.
The production of detonating gas can be prevented.
I don’t know.
On area A1 the function “Reception of shore to ship distress alerts” is mainly based on:
The use of MF DSC.
The use of Inmarsat-A.
The use of SART transponders.
The use of VHF DSC.
The hydrostatic release of an EPIRB should be changed:
Every 4 years.
Every 3 years.
Every 2 years.
Yearly.
Messages sent via Inmarsat-C are charged:
On the number of kilobits of information transmitted per block of 256 bits.
On the basis of a 3 minute minimum charge with 1 minute incremental steps.
On the number of kilobits of information transmitted per block of 1 024 bits.
On the basis of a 6 seconds minimum charge with 6 second incremental steps.
The steps of the embarkation ladder used must be proportioned as it follows:
Length = 280 mm, breadth = 85 mm, depth = 10 mm.
Length = 380 mm, breadth = 145 mm, depth = 20 mm.
Length = 480 mm, breadth = 115 mm, depth = 25 mm.
Length = 580 mm, breadth = 165 mm, depth = 30 mm.
The steps of the embarkation ladder used must be spaced apart by a distance of:
Equally spaced, not less than 300 mm or more than 380 mm.
Equally spaced, not less than 200 mm or more than 280 mm.
200 mm.
300 mm.
Give the meaning of the following symbol:
EPIRB.
Radar transponder.
Survival craft distress pyrotechnic signals.
Rocket parachute flares.
Which ships does the ISM code apply to:
All passenger ships, all cargo ships of 500 GRT or above.
Only tankers and Ro-ros.
All craft above 300 GRT.
Only passenger vessels.
What is a contingency plan for ships?
Plan for safety preparedness.
Loading plan for general cargo.
Plan for next voyage.
Plan for maintenance and repair.
HEL-H is the abbreviation of a heavy helicopter radius of action for rescue purposes. What do you think the radius and evacuating capacity of the helicopter is?
500 nm and capacity for evacuating more than 25 persons.
200 nm and capacity for evacuating more then 15 persons.
150 nm and capacity for evacuating more than 12 persons.
100 nm and capacity for evacuating more than 10 persons.
Who is the leader of the lifeboat drill (abandon ship drill)?
The first member of the crew arriving at the survival craft.
The appointed lifeboat commander.
Senior deck officer.
Senior engine officer.
What is a Continuous Synopsis Record?
A record of the vessels history.
A plan including all security measures onboard.
A record of all security incidents.
A plan for continuous maintenance of security equipment.
On a RoRo vessel, how should caterpillar crawlers stowed on hatch covers be secured?
By means of wire ropes or chains secured to the hatch covers and to the main deck from all four sides of the unit.
By means of wire ropes secured to the hatch covers from all four sides of the unit.
By means of wire ropes secured to the hatch covers from all four sides of the unit.
By means of wire ropes secured to the hatch coamings.
On a RoRo vessel, what should be done when cargoes that transmit stack loads are to be loaded onto the vessel’s decks or hatch covers?
Weld additional steel plates to the deck and/or hatch covers where stack loads are transmitted.
Stow the cargo on timbers of sufficient thickness so as to distribute the stack load.
Load the cargo under-deck instead.
Stow the full length of cargo on timbers of sufficient thickness.
On a RoRo vessel in a wet climate what can happen to wheeled cargoes?
The ship’s paintwork flaking and falling onto the cargo.
The lashings will become clean because of the water.
Lashings can become slack over time and the cargo is more likely to shift due to the wet weather.
The lashings will become clean because of the water.
Why is it important in a RoRo vessel to ensure that cargo is loaded in a uniform way?
Because it makes it harder to lash the cargo correctly if you don’t.
Because it looks better and image is important.
Because it looks better and image is important.
To prevent high sheer forces and bending moments on the vessel during the loading/discharge operations.
When will a ro-ro vessel pitch heavily?
When wave lengths are equal to the ship’s length.
When wave lengths are equal to half the ship’s length.
When wave lengths are equal to twice the ship’s length.
In confused seas.
What special design feature is attributed to RoRo vessels which are only car carriers?
A small GM when fully loaded.
A very large windage area.
A stern ramp.
Solid ballast.
What immediate action should be taken if a ship unexpectedly runs aground and stops?
Stop engine(s).
Stop engines and tell the engine room to switch over to high suctions.
Stop engines and immediately request “Full Astern”.
Sound the General Alarm and plot the ships position.
On a RoRo vessel, which of the ships trading certificates details the type and location that dangerous goods are allowed to be stowed onboard?
Safety Equipment certificate.
The Cargo Ship Safety construction certificate.
Certificate of compliance for the carriage of Dangerous goods.
I don’t know.
Under SOLAS, what are the minimum required air changes per hour for “Special Category Spaces” on a RoRo vessel?
8.
10.
15.
20.
A Standard Ro-Ro unit weighing 18 mt is to be loaded in the fore and aft direction and lashed by belts of SWL 2 mt. Using the general rule How many lashing belts should be used to secure the unit?
9 on each side.
10 on each side.
11 on each side.
One fore every securing point on the unit.
On a RoRo vessel, which of these situations will result in an emergency shutdown of cargo operations?
Any of the listed situations.
Failure of the cargo hold ventilation system.
The vessel developing a sudden and unexpected list.
I don’t know.
On a RoRo vessel, what must be ensured onboard the vessel prior to commencing cargo?
Cargo hold ventilation systems are operational.
That all cargo is ready for loading.
That the vessel has been cleared by immigration.
That all cargo is ready for loading.
On a RoRo vessel, to what should you pay very close attention, when inspecting the structure and condition of movable car decks?
General condition of the portable deck.
Crack in way of deck supports.
Abrasions over the deck surface.
General condition of the portable deck.
When lowering a RoRo Cargo Side or Stern Ramp what must be ensured?
The vessel is securely moored and there is nothing beneath the ramp.
The ramp must be lowered by the duty officer only.
The ramp must be lowered by the duty officer only.
The ramp surface must be clean.
On a RoRo vessel, where can you find the validity of web lashings?
It does not have one they last forever.
On the bridge.
On the certificate supplied with the equipment.
I don’t know.
On a RoRo vessel, what is the Maximum Securing Load of “D” rings?
50 % of the breaking strength.
40 % of the breaking strength.
35 % of the breaking strength.
25 % of the breaking strength.
On a RoRo vessel, when should a trailer horse be taken out of service?
If there is any damage to the wheel or spring, the frame is rusted or distorted or the pads are worn out.
Every 6 months for routine maintenance.
Every 3 months for routine maintenance.
Never you use them until they collapse.
Your vessel is approaching a port in restricted visibility and you hear this signal. What kind of vessel is it and what is it doing?
It comes from a vessel restricted in her ability to manoeuvre.
It comes from a vessel at anchor, less than 100 metres in length.
It comes from a vessel engaged in pilotage duties at anchor, over 100 metres in length.
It comes from a vessel engaged in pilotage duties and it is making way through the water.
What are the three volumes of the IAMSAR Manual?
I – Planning and Preparation, II – Rescue Control, III – Reference.
A – Command and Control, B – Communications, C – Rescue Procedures.
I – Organization, II – Communications, III – Rescue Procedures.
I – Organization and Management, II – Mission Coordination, III – Mobile Facilities.
DG placards shall be located on a freight container:
One on each end and one on each side.
One on each side (only).
One of the back end and one on one of the sides (only).
One on each end (only).
Substances, materials and articles shall be stowed as indicated in the Dangerous Goods List of the IMDG Code, in accordance with a series of stowage categories, which are designated a:
5 categories, labelled A-E.
10 categories, lattered A-K (excluding I).
10 categories, numbered 1-10.
Three categories, numbered I, II and III.
If the shipper wishes to ensure that a vessel or her operators will not be held responsible for any damage that may arise from the carrier issuing a clean Bill of Lading, even though the Mate’s receipt is marked as “unclean”, such a document is called the:
A Letter of Credit.
A Letter of Indemnity.
An addendum to the Bill of Lading.
An absolution clause in the shipping documents.
When conducting a risk assessment for a shipboard work activity, the two elements to be considered are:
The time available to complete the task and the resources to hand.
The available manpower and their experience in this type of work.
The chance of an incident re-occuring and the potential effects of an loss.
The potential severity of harm and the likelihood that harm will occur.
How often under SOLAS, is the performance test of a Voyage Data Recorder required by an approved testing or servicing facility?
Annually.
When the data media is downloaded.
When the battery is replaced.
At the Intermediate Safety Equipment Survey.
Where would you find the document relating to the “Condition of Freeboard Assignment” onboard?
With the Structural Survey File.
With the Loadline Certificate.
With the Classification Records.
With the Safety Construction Certificate.
Master of every ship must provide:
A link between the shipboard training officer and the company training officer ashore.
The training during crews working hours only.
Proper rest to the crew after each training programme.
Facilities to conduct training whenever required by the training officer.
Why is it important to have good relationship on-board a vessel?
It leads to better work performance and positive atmosphere among the crew.
Crew comes to know each other problems.
In encourages crew to extend their contract.
It will prevent accidents from happening.
What type of dynamic forces may cause indent in plating on forecastle deck and main deck in way of pillars inside forecastle?
Forces created by waves on the forecastle.
Slamming in way of flat bottom forward of light draught.
Impact pressure forces in way of abrupt or flared bow.
Pressure forces caused by green water on deck.
Who can contact the Designated Person with their safety concerns?
Captain.
Captain and Officers.
All crewmembers.
I don’t know.
Your ship security plan must include procedures for responding to security threats, auditing security activities and interfacing with the port facility.
True.
False.
The «Deck Management RoRo Cargo Vessel» subject provides both theoretical and practical information on safely working with electrical equipment. Proficiency in this area is a clear indicator of an employee's competence in a relevant role on a vessel. RoRo (Roll-On/Roll-Off) vessels are commonly used for short-sea shipping routes and ferry services, transporting cargo between various ports within a region or country. They also play a significant role in international trade, connecting major ports worldwide. RoRo vessels offer an efficient and cost-effective method for transporting large volumes of wheeled cargo over water, serving as a crucial link in global supply chains and supporting industries like automotive manufacturing and construction.
As an officer on a RoRo vessel, your responsibilities may include navigational tasks such as charting courses, monitoring weather conditions, and ensuring the vessel's safe passage. Additionally, you may supervise the loading and unloading of vehicles and cargo via the RoRo ramp, among other duties.
- Version: 6.0.0.
- Test type: STCW.
- Department: Deck.
- Level: Management.
- Vessel type: Ro-Ro Cargo Vessel.
Nur Segler können Bewertungen hinterlassen. Um eine Bewertung abzugeben, melden Sie sich mit Ihrem Sailor-Konto auf der Website an.
Seien Sie der Erste, der diesen Online-Test bewertet!